全自動五金噴涂設備生產線中英文技術要求

As discussed I have put together an RFQ for automated spray process.
全自動噴涂設備
液體-whitfords, xlar/xylan PET油漆
 
Product Range: Stud bolt, Hex bolt, Nut, Washer.
噴涂的產品：牙條，六角螺栓，螺母點墊片
 
產品尺寸：
Product Size:
牙條，六角螺栓Diameter直徑： ?” through to 4”, Length 長度：2” through to 70” (stud / Hex bolt)， Weight Max 重量：100kg
                    直徑： Diameter ?” through to 6” (Nut) 螺母
                    直徑：Diameter ?” through to 8” (Washer) 墊片

Items required in order of relevance:
項目的關聯性：

o    Programmable Overhead track 有軌道編程系統
o    Blast room (automated) quick media change capability 噴涂間有自動化快速變化能力
o    Pre Heat through oven up to 50°C 熱量在50度以上
o  Spray Booth with 2D spray capability for single side coating with paint thickness monitoring capability
噴漆柜與2 d為單邊噴霧功能涂料油漆厚度監控能力
o    Spray Booth with 2D spray capability for single side coating (opposite to above) with paint thickness monitoring capability     possibility to replace with 3D robot and allow only 1 booth pending material coverage.
噴漆柜與2 d為單邊噴霧功能涂料與油漆厚度(上面對面)監控功能可能與3 d機器人取代,只允許1個展位等待材料覆蓋。
o    Through Oven for flash up to 200°C (15-20 min) 15-20分鐘內烤箱溫度達到200度
o    Through Oven for Cure up to 600°C (30 min)30分鐘通過烤箱的溫度為600度
o    Free track to allow cooling up to 2 hours 冷卻時間為2小時

Currently I can produce maximum 13,492 pcs of ?” stud bolt in approximately 1hr 10 minutes from spray to cure (oven being constraint) before cooling…to make the track feasible I must have capability to reduce this time dramatically.
目前在1小時10分鐘通過噴涂，固化，冷卻，可生產的1/2 牙條為13492根



好品質-選榮德：榮德機器人歡迎您！20年研發自動噴涂設備經驗，國家級高新技術企業，七百平米實驗室提供免費試機打樣！免費試噴打樣熱線：138 2368 0921 白小姐 噴涂視頻：http://m.amylowe.com/